15 years of academic expertise Trusted by students in 27 countries
Student studying with an online tutor

Free 15-minute tutor consultation

A tutor reviews your brief and the Pass, Merit and Distinction criteria with you and gives you a clear plan for your own work.

HND Assignment Help logo
Packet Tracer Network Design Assignment Help: Topology, IP Plan and Testing Guide

Packet Tracer Network Design Assignment Help: Topology, IP Plan and Testing Guide

Last updated: November 2026 · Reviewed by the HND Assignment Help tutoring team

Quick answer

A Packet Tracer network design assignment asks you to design a network for a scenario, build and configure it in Cisco Packet Tracer, and write a report that justifies and tests your design. Deliverables are usually a .pkt file and a report. Most marks go to a clear IP addressing plan, correct VLAN and routing configuration, and documented testing that proves each requirement works.

Packet Tracer at a glance

ItemDetail
ToolCisco Packet Tracer (Cisco Networking Academy)
Where it is usedUK computing and networking degree modules and HND Computing courses
Typical deliverablesPacket Tracer (.pkt) file plus a design and testing report; check your brief
Core skillsRequirements analysis, topology, VLSM addressing, VLANs, routing, DHCP, ACLs
Where marks usually sitJustified design, working configuration, test evidence, critical evaluation
Unit factsLearning outcomes, weighting and word count differ by course; check your module handbook

Stuck on Packet Tracer Network Design Assignment Help: Topology, IP Plan and Te…?

Send us your brief. A UK tutor will explain what the marking criteria are asking for and help you plan your answer. Your first consultation is free.

WhatsApp a tutorGet a free quoteCall us

How to approach a Packet Tracer network design assignment

Cisco Packet Tracer is a free network simulation tool from the Cisco Networking Academy. UK universities and colleges use it in networking modules on computing degrees and HND Computing courses, where students design a network for an imagined organisation, build it in a .pkt file and write a report. The exact devices, services and marks vary, so read your brief first and turn every requirement into a line in your plan.

Step 1: Turn the scenario into requirements

Make a requirements table before you open Packet Tracer. It stops you missing marks and gives your report a clear thread from need to design to test.

Requirement (from your brief)Design decisionHow you will test it
Separate departmentsOne VLAN per departmentshow vlan brief; ping within and across VLANs
Devices get addresses automaticallyDHCP pool per VLANPC shows correct IP, mask and gateway
Two sites connectedRouted WAN link with a routing protocolshow ip route; tracert between sites
Guests kept off staff networkSeparate SSID or VLAN plus ACLGuest ping to staff server fails
Basic securityPasswords, SSH, port securityLogin test; port shutdown on violation

Step 2: Choose and justify a topology

Most briefs reward a hierarchical design: an access layer for end devices, a distribution layer for routing between VLANs and a core or edge layer for the WAN or internet link. Justify your choice with scalability, redundancy and cost. If you add redundant links, mention how Spanning Tree Protocol prevents loops. Include a labelled logical diagram in the report, not just a screenshot of the canvas.

Step 3: Build an IP addressing plan with VLSM

Variable Length Subnet Masking lets you size each subnet to the hosts it needs, which shows efficient use of address space. Always allocate the largest subnet first.

Worked method example (not an answer)

This uses an invented network to show the method only. Suppose you are given 192.168.10.0/24 for a site with Sales (100 hosts), Admin (50 hosts), IT (20 hosts) and one point-to-point WAN link.

SubnetHosts neededPrefixNetworkUsable rangeBroadcast
Sales100/25 (126 usable)192.168.10.0.1 to .126.127
Admin50/26 (62 usable)192.168.10.128.129 to .190.191
IT20/27 (30 usable)192.168.10.192.193 to .222.223
WAN link2/30 (2 usable)192.168.10.224.225 to .226.227

The rule is: usable hosts = 2 to the power of host bits, minus 2. A /26 leaves 6 host bits, so 64 minus 2 gives 62. Show this working in your report and say how much room each subnet leaves for growth. Your own scenario will have different numbers.

Step 4: Configure in a sensible order

Build in layers and save often: device names and passwords, VLANs and trunk links, inter-VLAN routing (router-on-a-stick sub-interfaces or a Layer 3 switch), DHCP, routing between sites (static routes or a dynamic protocol such as OSPF, as your brief asks), then services and security such as ACLs, SSH and port security. Keep a configuration log of the commands you used for each device; it helps when something breaks and can go in an appendix if your brief allows.

Step 5: Test and document evidence

Testing is where many marks sit. Write a test plan with an expected result before you run each test, then record the actual result and a screenshot.

TestCommand or actionExpected result
Interface statusshow ip interface briefRequired interfaces up/up
VLAN membershipshow vlan briefPorts in the correct VLANs
Routingshow ip routeRoutes to all remote networks
End-to-end reachabilityping and tracert from a PCReplies and the expected path
Security rulePing from guest to staff serverRequest blocked by ACL

If a test fails, record it, fix it and retest. A short troubleshooting note that explains the cause shows real understanding.

Common mistake

Building a network that works but not explaining why it is designed that way. A screenshot of a busy canvas earns little on its own. Assessors want the link from each requirement to a design decision and then to a test that proves it, plus an honest evaluation of limits such as single points of failure.

How assessors judge Packet Tracer

What they look forWeak answerStrong answer
RequirementsNot statedEvery brief requirement listed and traced
AddressingRandom addressesVLSM plan with working shown and growth room
ConfigurationPartly workingVLANs, routing and services working as specified
TestingOne ping screenshotTest plan with expected and actual results
EvaluationNoneLimits, security risks and future improvements discussed

Want a tutor to check your draft first?

Get clear written feedback on your own work before the deadline: structure, criteria coverage and referencing. Feedback on your own draft starts from £45, and tutoring from £32 an hour.

WhatsApp a tutorGet a free quoteCall us

Pre-submission checklist

  • Every requirement in the brief appears in your requirements table.
  • Your addressing plan has no overlapping subnets and shows the working.
  • Device names, interface labels and the diagram match the .pkt file.
  • Each test has an expected result, actual result and evidence.
  • You saved the final .pkt file and opened it again to check it loads.
  • The report includes evaluation and future improvements.
  • References and figure captions follow your course style.

Stuck on your Packet Tracer design?

A networking tutor can explain subnetting, VLAN and routing concepts, review your test plan and give feedback on your report. Ask for our free network design report template.

WhatsApp a tutorGet the free template

Packet Tracer answer hints and sample structure

We do not provide a finished .pkt file or report to submit. Use this structure to plan your own report and adjust it to your brief and marking scheme.

SectionWhat goes in itSuggested share
Introduction and requirementsScenario summary and requirements table10%
Logical and physical designTopology choice, diagram, device choice and justification20%
Addressing planVLSM table and working15%
Configuration summaryVLANs, routing, DHCP, security, key commands20%
TestingTest plan, results, troubleshooting20%
Evaluation and conclusionLimits, risks, improvements15%

Deadline coming up?

Book a 1-to-1 online session today. Tutors are available 7 days a week, 8am–11pm, and usually reply within 2 hours.

WhatsApp a tutorGet a free quoteCall us

Packet Tracer FAQs

What is Cisco Packet Tracer?

Cisco Packet Tracer is a free network simulation tool from the Cisco Networking Academy, used to design, configure and test networks without physical equipment.

What should a Packet Tracer report include?

Usually a requirements analysis, network diagram, IP addressing plan, configuration summary, test plan with results, and an evaluation. Check your brief for required sections.

How do I work out VLSM subnets?

List subnets from largest to smallest, choose the smallest prefix that fits each one using usable hosts = 2 to the power of host bits minus 2, then allocate them in order without overlaps.

Router-on-a-stick or a Layer 3 switch?

Both provide inter-VLAN routing. A Layer 3 switch usually scales better, while router-on-a-stick is simple for small networks. Choose based on your brief and justify it.

Should I use static routing or OSPF?

Use what your brief asks for. Static routes suit very small networks; a dynamic protocol such as OSPF adapts to changes and scales better.

Why does my ping fail between VLANs?

Common causes are a missing trunk, wrong sub-interface encapsulation, a wrong default gateway on the PC, or an ACL blocking traffic. Test step by step.

Can you build my Packet Tracer file for me?

No. We provide tutoring and feedback so you can build, test and write up your own network.

Share your brief

Send your unit brief and criteria. We match you with a tutor who knows your awarding body.

Free trial class

A 15–20 minute live session where the tutor breaks down the criteria and gives you a plan.

Learn and improve

Book more 1-to-1 sessions if it helps, and get feedback on your own drafts before you submit.